VELVET, PHOTOWALL-PAPER OR WOODEN WALLS

Along with traditional materials for furnish of walls it is possible to use a chintz, a velvet, an oilcloth. For chintz and velvet gluing use various glues and mastics. Is better for this purpose usual paste from a flour or starch with addition of joiner's glue approaches. Paste is convenient that if it is required to remove a chintz or a velvet, will enough moisten these materials with water; they also will easily act in film. To smear a fabric as wall-paper, it is impossible: paste will get on an obverse surface and at, it will shine. Therefore preliminary a wall surface cover with the prepared paste and allow to dry up to such condition when to it fingers of hands still stick. Then impose a fabric and carefully smooth through a paper. Hands thus should be dry and pure, without paste traces.

It is possible to fix cloths to a wall by means of laths in width of 20 mm. To their back party fix thin carnations a material, and then a lath with a material fix to a wall. In walls bore through apertures, insert there wooden stoppers and into them through a lath hammer in nails.

Some strengthen a cloth by means of a kapron scaffold. In corners of walls fix nails. Through the sewed cloth pass a kapron thread, hardly pull, nails assign, straighten a material.

With oilcloth usually paste over walls in a bathroom, a toilet, is more rare on kitchen. If surfaces of walls have not been laid out earlier by a tile, as a rule, they equal enough and additional processing do not demand. Wash out their warm soap water, well dry up, ground drying oil. After tiles often there are traces of a solution or mastic on walls. DELSAM, recommends them to remove, a wall surface to grind a fine-grained skin, to wash out and. For oilcloth gluing use glue "Bustilat". At first glue a surface of walls, then smear a cloth with gluing structure, drive him into the corner and carefully smooth, paying special attention on edges which often come unstuck from walls.

Gluing of photowall-paper

Sometimes photowall-paper pastes on a door. In that case, to increase term of their service and to make more attractive, it is recommended after they it is completely dried up, to cover with their colourless varnish. Pay attention to that thus wall-paper was absolutely pure, without the slightest traces of paste on surfaces, differently on the failures covered with a varnish there will be white divorces and strips which can spoil all work. Is better to varnish from a spray then the surface of failures will be equal, without excessive shine and interior design from it only will win.

Furnish of walls by a tree

First of all, calculate demanded quantity of a material, get the necessary tool, it must be done as well before you will start to make apartment repair. It is the most convenient to use a ready material: a board in the thickness of 22-26 mm, so-called. The material should be well dried up and not bent. It is possible to use and an edging or not edging board. In this case process board face sheet a manual plane or on the small-sized woodworking machine tool. By means of a plane-otbornika or the special adaptation on the machine tool choose a quarter (fig. 6). Depending on length define how to beat boards: vertically or horizontally. Usually in apartments height from a floor to a ceiling of 2,5-2,7 m. If the length of a material corresponds to these sizes, boards are more preferable for beating vertically if less — it is horizontal. It is necessary to consider that the premise area (a hall, a hall or kitchen) after furnish by a tree will decrease for a thickness of a board in case to fix each board directly to a wall.

In modern apartments where European-quality repair is not made yet, walls, as a rule, concrete and to fix each board difficultly: it is necessary to drill an aperture in a wall, to hammer into it in a wooden stopper or, to wrap a screw. In this case without not to manage.

To thicket arrive so: distance from a floor to a ceiling divide into 3, 4 parts and by means of screws horizontal laths in the thickness of 20-25 mm and width 60—80 mm fix to a concrete wall. After that nail up boards to laths in length of 40 mm. In the course of work watch, that "vertical position" of boards was not broken and a crack between them were minimum. For this purpose each subsequent board slightly line to already beaten before to fix a nail.

If the length of boards is less, than height from a floor to a ceiling, it is expedient to have them horizontally. In this case laths fix vertically on distance of 600 700 mm from each other. Start to beat boards from below. Thus each subsequent board a quarter will close the previous.

The joint place between end faces of the next boards is better for closing a wooden overlay or the furniture to arrange so that places of joints were not visible. Then carefully examine a surface, apertures from the beaten out knots, nails, liquidate other defects of boards.

Can prepare: dissolve glue under the instruction, add there small wood sawdust, carefully move. After the prepared weight will harden a little, wooden close up all defects of boards. That did not follow from apertures and cracks, paste on them small pieces of a paper. Drying time 18—24 hours. After that all surface of boards along fibres grind a fine-grained skin, carefully remove a dust a brush or by means of the vacuum cleaner. Varnish a wooden surface. It is better to use a furniture varnish, for example NC-222. Put usually two - three varnish coats. Time of drying of one layer 1—2 hours.